![Show Menu](styles/mobile-menu.png)
![Page Background](./../common/page-substrates/page0079.jpg)
Sheave Dimension Information - According to ARPM (RMA)
Standard IP-22 (2007) (3V, 5V, 8V, 3VX, 5VX)
SHEAVES
Groove Dimensions:
Groove angles and dimensions for sheaves shall conform to Table I-1 and Figure I-1 or Figure I-2.
Face Width of Sheaves:
Face width of sheaves for multiple belt drives shall be in accordance with Table I-1 and
Figure I-1 or I-2.
Keyways for Sheaves:
Keyways in the hubs of sheaves shall conform to the dimensions and tolerances shown in
MPTA-B1 - Bore and Keyway Tolerances for V-Belted Sheaves.
Balance:
Sheaves shall be balanced to conform to MPTA-B2C - Standard Practice for Sheave/Pulley Balancing.
Finish:
The machined surface finish of various areas of transmission sheaves shall conform with MPTA-B4 -
Standard Surface Finish for Transmission Pulleys.
These standards are available at
www.mpta.org.OTHER SHEAVE TOLERANCES
Outside Diameter:
Up through 8.0 inches outside diameter ± 0.020 inches. For each additional inch of outside
diameter, add ±0.005 inches.
Radial Runout**:
Up through 10.0 inches outside diameter 0.010 inches. For each additional inch of outside diameter,
add 0.0005 inches.
Axial Runout**:
Up through 5.0 inches outside diameter 0.005 inches. For each additional inch of outside diameter,
add 0.001 inches.
Face Width of Standard and Deep Groove Sheaves:
Face Width = S
g
(N
g
-1) + 2S
e
Where: N
g
= Number of Grooves
**
Total Indicator Reading
Figure I-1 - STANDARD GROOVE DIMENSIONS
SHEAVES
Groove Dimensions
. Groove angles and dimensions for
sheaves shall conform to Table II-1 and Figure II-1.
F ce Width of Sheaves
. Face width of sheaves f r multiple belt
drives shall be in accordance with Table II-1 and Figure II-1 or
II-2.
Keyways for Sheaves
. Keyways in the hubs of sheaves shall
conform to the dimensions and toler
ances shown in MPTA - B1
-- Bore and Keyway Tolerances for V-Belted Sheaves.
Balance
. Sheaves shall be balanced to conform with
MPTA -
B2C -- Standard Practice for Sheave / Pulley Balancing.
Finish
. The machined surface finish of various areas of
transmission sheaves shall conform with
MPTA - B4 -- Standard
Surface Finish for Transmission Pulleys.
These standards are available at
www.mpta.org.
OTHER SHEAVE TOLERANCES
Outside Diam ter:
Up through 200 mm out ide diameter ±0.5
mm. For each additional 25 mm of outside diameter add ±0.05
mm.
Radial Runout*:
Up through 250 mm outside diameter 0.25
mm. For each additional 25 mm of outside diameter add 0.01
mm.
Axial Runout*:
Up through 125 mm outside diameter 0.13
mm. For each additional 25 mm of outside diameter add 0.03
mm.
Face Width of Standard an Deep Groove Sheaves:
Face Width = S g (N g -1) + 2S e
Where: N g = Number of Grooves
*Total Indicator Reading
All rights r erved. The c tents of this publicati
may not be reprinted
or otherwise reproduced in any form without the express written permission of RMA.
RMA IP-22 (2007)
Part 1 (Inch-Pound Units)
TECHNICAL DATA
POWERING GLOBAL INDUSTRY
TECHNICAL DATA
77