56
Tel: +1.314.739.9191 • +1.800.288.2726 • Fax: +1.314.739.5880 •
www.tapcoinc.comAC & MF
NYLON
ELEVATOR BUCKETS
STYLE AC BUCKETS
450-260
610-260
18 X 10
24 X 10
19
25
11
10-3/4
10.4
15.5
.654
.781
.491
.586
11-1/2
11
1130.1
1349.6
847.6
1012.2
Size
(Nominal)
Inches
Size
(Nominal)
Millimeter
Dimensions-Actual (Inches)
Tolerance A, B & C
±
1/4" T
±
1/32"
Length
A
Proj.
B
Depth
C
Gross X-X
Usable
Cu. In.
Cu. Ft.
Cu. In.
Cu. Ft.
Weight
(Pounds)
Capacity
Tolerance
±
3%
STYLE MF BUCKETS
260-125-180
300-200-280
10 X 5 X 7
12 X 8 X 11
10
12-1/4
5
8
2.1
5.5
.102
.301
.077
.226
7-3/4
11-5/8
176.3
520.1
132.2
390.1
Size
(Nominal)
Inches
Size
(Nominal)
Millimeter
Dimensions-Actual (Inches)
Tolerance A, B & C
±
1/4" T
±
1/32"
Length
A
Proj.
B
Depth
C
Gross X-X
Usable
Cu. In.
Cu. Ft.
Cu. In.
Cu. Ft.
Weight
(Pounds)
Capacity
Tolerance
±
3%
STYLE:
AC & MF
DESIGN:
Centrifugal discharge.
material:
Nylon
METHOD OF MANUFACTURE:
Cast.
COLOR
:
Black.
TEMPERATURE RANGE:
+20° F to + 300° F. (-7° C to +149° C).
DRILLING:
No charge for standard belt or chain drillings when order totals
50 or more pieces of the same size. Contact Tapco for quotation on
orders of less than 50 and/or special drill pattern requirements.
VENTING:
Standard on AC, with four 9/32" diameter holes.
USABLE CAPACITY:
Tapco recommends using 75% of gross,
(100%) capacity.
SPACING:
A common minimum spacing would be nominal projection
plus 4", however both closer and greater spacings may be used
depending upon the application.
RECOMMENDATIONS:
AC & MF nylon buckets are ideal for use
with foundry sand, gravel, coal, fertilizer, clay, salt, and many other
industrial materials.
INTERCHANGEABILITY:
Can be intermixed with existing cast iron,
fabricated steel, or nonmetallic buckets. Some care should be
taken that the leg does not become too far out of balance. Bucket
projection varies by manufacturer and material. Check elevator for
proper clearances. Contact Tapco for recommendations.
INSTALLATION:
On belt:
Fanged elevator bolts and nylon insert lock
nuts are recommended.
Large flat (fender) steel washers must be
placed inside the bucket under the nuts.
On chain
: Use Grade 5 hex head bolts with hex nuts, large flat (fender)
washers, and lock washers.
Elevator bolts should not be used on
chain attachments.
CAUTION:
Welding and cutting on elevator legs without taking proper
precautions is extremely dangerous and can cause a violent explosion.
NYLON TECHNICAL INFORMATION:
IMPORTANT:
When elevating certain materials that harden or setup with moisture, a Tapco metallic digger bucket should replace every 10th urethane
bucket. Contact Tapco for recommendations.
End View
Front View
End View
Front View