Goodyear Rubber Products
CALL
TOLL FREE
IN THE USA
1-866-711-4673
INTERNATIONAL SALES CALL
+1-727-342-5086
WE SHIP WORLDWIDE
International Sales Click Here
Get A
Quote
Now
Home
About Us
Product Brands
Catalogs
Contact Us
Locations
Corporate Headquarters,
Clearwater, Florida, (FL)
Parker Store, Bradenton, Florida, (FL)
Parker Store, St. Petersburg, (FL)
Parker Store, Ft. Myers, Florida, (FL)
Parker Store, Naples, Florida, (FL)
Parker Store, Tampa, Florida, (FL)
<< Previous Page
Click Here
to open this page in a new window.
Next Page >>
Catalog 4400 US Equipment Parkrimp Assembly Instructions Crimping using Superkrimp and Parkrimp 2 Parkrimp Fittings Series 25, 26, 43, 70, 71, 73, 76, 78, S6, 81, HY Mark insertion depth and push on fitting If using large two-piece dies 1 2a Insert the proper die For 81 Series Shells with 88 Series Fittings set into the die bowl. (The die sets are in two halves of four dies each. Place one A half in the back and one half in the front to accommodate bent tube fittings.) Reference decal on crimper for proper Mark the hose insertion depth tool selection. and push hose into fitting until thePlace 81 Series Push hose onto the mark on the hose is even with theShell onto end of 88 Series fitting until end of the shell. Lubricate hose hose and make the shell bottoms if necessary, however, DO NOT sure the end of the against the fitting's lubricate if using spiral hose. shell lines up with stop ring or hex. See Hose Insertion Depth table the Insertion Depth Lubricate hose if on previous page. mark. necessary. If using small unitized dies Place spacer ring 2b 3 B Slide Pin Color-Coded Unitized Die-Train With the pusher in the Lubricate die bowl using a Lubricate die bowl using a premium If required, place spac- full up position, lift the premium quality lithium- quality lithium-base grease. Place unitized die-er ring on locating step back half of the split die base grease. Carefully train into the adapter bowl. Select die of adapter bowl. Refer- C ring. Lock it in the up insert the adapter bowl, and die ring by hose size and type. See ence decal on crimper position by pushing the 83C-OCB, into the base decal on crimper for proper die set. for tool selection. slide pin in. (The slide bowl. The adapter bowl Note: Die sets have color-coded cavities indicat- pin is located inside the must be tilted toward the ing size and have the fitting series pusher at the back.) back of the crimper during and dash size stamped on the top. insertion. Position the split die ring 4 5 Position the fitting Parkrimp Series 26Series 81 Series Slide Pin D Position the hose and fitting in dies from below. Rest bottom of coupling on die step using the PARKALIGN� feature. Lower the back half of the Insert the front half of the Parkrimp Measure crimp diameter TechnicalAccessoriesHoseFittings split die ring onto the dies bysplit die ring aligning the 7 Equipment pulling the slide pin forward.pins in the back half with the hole in the front half. Measure crimp Standard 26 Series Crimp hose diameter on the Parkrimp Series 6 flat surfaces of the crimped shell, Turn on the pump by pressing the "ON" switch. referenced in the Pull the valve handle forward to bring the pusher illustration to the down for crimping. When the split die ring con- right. Reference Crimp tacts the base plate, the crimp is complete. Push decal on crimper Diameter the valve handle back to lift the pusher, open the for crimp diam- dies, and release the finished assembly. E eters. Never use Note: You do not have to remove any tooling to hose assemblies insert or remove straight fittings. The front half of with incorrect Important: Hose assemblies the split die ring and the front die train must be crimp diameters. must be inspected for cleanliness removed to insert and remove bent tube fittings. and free of all foreign particles. C- Hose Products Division Parker Hannifin Corporation Wickliffe, Ohio
Goodyear Rubber Products
