11
C O N Q U E S T X P
™
*
Average Permanent Elongation values at 100% of rated belt tension are based on ISO 9856 test procedure. Consult your GTM or GAD for elastic & total elongation calculations
specific to each system based on Minuteman calculations.
On systems with troughing idler spacing greater than 1.5m. or idler roll gap greater than 12.7mm, consult your GTM.
If top cover and pulley cover are balanced (i.e. 4.7mm x 4.7mm) or less than 1.5mm differential (ie. 4.7mm x 3.9mm), add 152mm to the minimum belt width. 152mm narrower widths are
possible if the belt is broken in for an extended period of time fully loaded.
Additional break-in time is required when the belt has been stored prior to installation in ambient temperatures of less than 10 degrees Centigrade.
Note: The minimum cover for vulcanized splice is 2.4mm
The recommended is maximum top to bottom cover ratio for one ply is 2 to 1
(
example is 4.5mm x 2.25mm) and for two ply is 3 to 1 (example is 9mm x 3mm)
Above tables are based on top cover gauge equal or greater than the bottom (pulley) cover gauge
Plies
Fabric Type
Vulcanized & Fastener Rating (kN/m)
Nominal carcass gauge (mm)
Nominal carcass weight (kg/sq.m)
Approximate 1/32" cover weight (kg/sq.m)
Average Permanent Elongation (%)*
Average Elastic Modulus (kN/m)
Step Length (mm)
Recommended Fasteners Plate
MaterialWeight
Trough Angle
330/1
440/1
660/2
880/2
Idlers
20
degree
35
degree
45
degree
Over 80% tension
60% - 80%
tension
40% - 60%
tension
Up to 40% tension
Tails and Snubs
ConquestXP 330/1
450
600
600
ConquestXP 330/1
450
400
350
300
300
ConquestXP 440/1
450
600
750
ConquestXP 440/1
500
450
400
350
350
ConquestXP 660/2
600
750
900
ConquestXP 660/2
600
500
450
100
400
ConquestXP 880/2
750
900
1050
ConquestXP 880/2
750
600
500
450
450
20
1500
1650
2300
2450
20
1550
1650
2150
2300
20
1350
1550
2150
2300
20
1200
1350
1850
2150
35
1350
1550
2150
2300
35
1350
1550
2000
2150
35
1200
1350
1850
2150
35
1050
1200
1650
2000
45
1350
1550
2150
2150
45
1200
1350
1850
2000
45
1050
1350
1650
2000
45
900
1050
1350
1650
0-640
kg/m
3
641-1280
kg/m
3
1281-1920
kg/m
3
Over 1920 kg/m
3
1
Dual Layer Twill (P/N)
58
3.3
3.6
0.19
1.00%
5,779
Finger Splice
BR6
R5
U35
1
Dual Layer Twill (P/N)
77
3.6
4.1
0.19
1.00%
6,130
Finger Splice
BR6
R5
U35
2
Dual Layer Twill (P/N)
116
6.9
7.9
0.19
1.20%
11,559
Finger Splice
BR10
R5-1/2
U35
2
Dual Layer Twill (P/N)
154
7.7
9.3
0.19
1.20%
12,259
Finger Splice
BR14
R6
U37/U37A
ConquestXP 330/1
ConquestXP 440/1
ConquestXP 660/2
ConquestXP 880/2
Hinge
Hinge
ConquestXP
™
Conveyor Belt Data - Metric
ConquestXP Load Support (Maximum Belt Width) (mm)
ConquestXP Troughability Support (Minimum Belt Width) (mm)
ConquestXP Minimum Pulley Diameters (mm)