10
C O N Q U E S T X P
™
*
Average Permanent Elongation values at 100% of rated belt tension are based on ISO 9856 test procedure. Consult your GTM or GAD for elastic & total elongation calculations
specific to each system based on Minuteman calculations.
On systems with troughing idler spacing greater than 5 ft. or idler roll gap greater than, 1/2" consult your GTM.
If top cover and pulley cover are balanced (i.e. 3/16" x 3/16") or less than 1/16" differential (ie. 3/16" x 5/32"), add 6" to the minimum belt width. 6" narrower widths are possible
if the belt is broken in for an extended period of time fully loaded.
Additional break-in time is required when the belt has been stored prior to installation in ambient temperatures of less than 50 degrees Fahrenheit.
Note: The minimum cover for vulcanized splice is 3/32"
The recommended is maximum top to bottom cover ratio for one ply is 2 to 1
(
example is 1/4" x 1/8") and for two ply is 3 to 1 (example is 3/8" x 1/8")
Above tables are based on top cover gauge equal or greater than the bottom (pulley) cover gauge
Plies
Fabric Type
Vulcanized & Fastener Rating (piw)
Nominal carcass gauge (inch)
Nominal carcass weight (lbs/sq.ft.)
Approximate 1/32" cover weight (lbs/sq.ft.)
Average Permanent Elongation (%)*
Average Elastic Modulus (piw)
Step Length
Recommended Fasteners Plate
Idlers
20
degree
35
degree
45
degree
Over 80% tension
60% - 80%
tension
40% - 60%
tension
Up to 40% tension
Tails and Snubs
ConquestXP 330/1
18
24
24
ConquestXP 330/1
18
16
14
12
12
ConquestXP 440/1
18
24
30
ConquestXP 440/1
20
18
16
14
14
ConquestXP 660/2
24
30
36
ConquestXP 660/2
24
20
18
16
16
ConquestXP 880/2
30
36
42
ConquestXP 880/2
30
24
20
18
18
20
60
66
90
96
20
60
66
84
90
20
54
60
84
90
20
48
54
72
84
35
54
60
84
90
35
54
60
78
84
35
48
54
72
84
35
42
48
66
78
45
54
60
84
84
45
48
54
72
78
45
42
54
66
78
45
36
42
54
66
0-40
lbs./cu.ft.
41-80
lbs./cu.ft.
81-120
lbs./cu.ft.
Over 120 lbs./cu.ft.
1
Dual Layer Twill (P/N)
330
0.13
0.73
0.19
1.00%
33,000
Finger Splice
BR6
R5
U35
1
Dual Layer Twill (P/N)
440
0.14
0.85
0.19
1.00%
35,000
Finger Splice
BR6
R5
U35
2
Dual Layer Twill (P/N)
660
0.27
1.61
0.19
1.20%
66,000
Finger Splice
BR10
R5-1/2
U35
2
Dual Layer Twill (P/N)
880
0.305
1.9
0.19
1.20%
70,000
Finger Splice
BR14
R6
U37/U37A
ConquestXP 330/1
ConquestXP 440/1
ConquestXP 660/2
ConquestXP 880/2
Hinge
Hinge
ConquestXP
™
Conveyor Belt Data - Imperial
ConquestXP Load Support (Maximum Belt Width) (inch)
ConquestXP Troughability Support (Minimum Belt Width) (inch)
ConquestXP Minimum Pulley Diameters (inch)
Material Weight
Trough Angle
330/1
440/1
660/2
880/2