Page 495 - 4300 Catalog Cover.pdf

4300 Catalog Appendix
V9 Parker Hannifin Corporation
Tube Fittings Division
Columbus, Ohio
http://www.parker.com/tfd
Table V13 — Hydra-Tool Recommended Pre-Setting Pressures for Inch Tube
1) These values are provided as a guide only and normally will produce a satisfactory bite.
2) Ferulok pre-setting dies are positive stop dies. Use of above pressures is optional.
3) For wall thicknesses greater than those listed, contact the Tube Fittings Division.
Table V12 — Pre-Setting Pressures for Steel and
Stainless Steel EO-2 Fittings
NOTE: The values provided in this chart are provided as a
guide only and normally will produce a satisfactory bite when
using the Parker Hydra-Tool.
Hydra-Tool Pre-Setting Pressures for EO and EO-2 Steel Fittings
Table V11 — Pre-Setting Pressures for Steel EO Fittings
NOTE: The values provided in this chart are provided as a guide only and
normally will produce a satisfactory bite when using the Parker Hydra-Tool.
Pre-Setting Tools
Pressures for Steel EO Fittings
Using Stop Adapter (971107 & 971108)
Pressures for Steel EO-2
Fittings Using Stop Adapter
(971107 & 971108)
Hydra-Tool Pre-Setting Pressures for Ferulok Fittings1) 2) 3)
Tube
Size
Wall Thickness – Steel Wall Thickness – Stainless Steel
0.035 0.049 0.065 0.083 0.095 0.109 0.120 0.035 0.049 0.065 0.083 0.095 0.109 0.120
4 300 300 500 600 600 600 300 300 500 700 700 700
6 300 500 600 700 700 700 700 300 500 700 700 700 700 800
8 500 700 800 900 1,000 1,000 600 700 1,000 1,000 1,100 1,100
10 700 900 1,000 1,100 1,100 800 1,000 1,100 1,300 1,300
12 900 1,000 1,100 1,100 1,300 1,000 1,100 1,300 1,300 1,500
14 1,000 1,100 1,100 1,300 1,500 1,000 1,300 1,300 1,500 1,600
16 1,100 1,300 1,500 1,600 1,500 1,500 1,600 1,600
20 1,500 1,600 1,800 1,600 2,000 2,000
24 1,800 2,000 2,300 2,100 2,300 2,300
32 2,800 2,900 3,300 3,100 3,300 3,300
Pre-Setting Pressues (psi) for EO Fittings
Wall Thickness (mm)
Size Series 1.0 1.5 2.0 2.5 3.0 4.0
6 L 500 500 500
6 S 500
8 L 500 500
8 S 500 500
10 L 500
10 S 500
12 L 300 300 500
12 S 300
14 S 1,500
15 L 500 800
16 S 1,200 1,300
18 L 1,000 1,300
20 S 2,000
22 L 1,500 1,500
25 S 2,000 2,000
28 L 2,000
30 S 3,000
35 L 3,000 3,300
38 S 3,500
42 L 4,000
Hydra-Tool
Pre-Setting Pressures (psi)
for EO-2 Fittings
in Steel and Stainless Steel
Using the Stop Adapter
Size Series psi
6 L 1,100
6 S 1,100
8 L 1,300
8 S 1,300
10 L 1,800
10 S 1,800
12 L 2,000
12 S 2,000
14 S 2,300
15 L 2,300
16 S 3,000
18 L 3,000
20 S 4,100
22 L 3,100
25 S 5,500
28 L 3,700
30 S 6,600
35 L 5,300
38 S 8,400
42 L 7,600
Dimensions and pressures for reference only, subject to change.