Page 424 - 4300 Catalog Cover.pdf

4300 Catalog Assembly / Installation
Parker Hannifin Corporation
Tube Fittings Division
Columbus, Ohio
http://www.parker.com/tfd
T14
Flanging Steps:
1. Determine the extra cut-off length required for the
Parflange process by referring to Tables T9 and T10. (Each
table is only a guide. Variations in tube wall thickness and
inconsistency in quality of tube cut-off may affect actual
dimensions. User should verify actual extra tube cut-off
length with one or two flanges prior to large scale flang-
ing.)
2. Select the proper tooling for the tube size. The tube OD,
wall thickness and material must be known for proper
selection. Refer to Table S5 on page S26 for flanging capa-
bility by Parflange machine and availability of tooling
3. With the sleeve properly positioned within the die set,
place the set into the die holder of the machine.
4. Insert the tube through the die opening until it comes in
contact with the tube stop. Do not forget to position the
tube nut over the tube in the proper orientation, especially
if the other tube end has already been flanged, or the tube
has sharp bends.
5. Flange the tube as shown in Figure T16.
Note: For more information on Parflange procedures, ma-
chines, etc., Contact Parker.
Fig. T17 – Extra cut-off length
Table T9 – Extra tube cut-off length guide for inch tube
Table T10 – Extra tube cut-off length guide for metric tube
Seal-Lok Assembly
Tube
O.D.
(in.)
Tube Wall Thickness – Inch
.028 .035 .049 .065 .083 .095 .109 .120 .134 .156 .188
1/4 3/16 13/64 5/32
3/8 9/64** 9/64 5/32 5/32 5/32
1/2 5/32** 9/64 9/64 9/64 9/64
5/8 5/32 5/32 7/64 11/64 5/32 11/64
3/4 5/32* 5/32 5/32 1/8 7/64 9/64 5/32 11/64
1 9/64* 9/64* 9/64 9/64 7/64 11/64 11/64 316
1 1/4 5/32 7/64 7/64 1/8 5/32 11/64 11/64
1 1/2 11/64 11/64 3/16 3/16 3/16 3/16 15/64 7/32
Tube
O.D.
(in.)
Metric Tube Outside Diameter (mm)
6 8 10 12 14 15 16 18 20 22 25 28 30 32 35 38
1.0 4.5 5.5** 2.5** 3.5** — 5.0
11/64 7/32 3/32 9/64 13/64
1.5 5.5 5.0 4.0 4.5** 4.5 4.5 3.0 6.0
7/32 13/64 5/32 11/64 11/64 11/64 1/8 15/64
2.0 3.5 4.5 6.0 5.0 3.0 5.5 4.0 6.5 4.5 6.0 5.0 — — 5.5
9/64 11/64 15/64 13/64 1/8 7/32 5/32 1/4 11/64 15/64 13/64 7/32
2.5 4.5 5.5 5.0 3.5 6.5 4.0 7.0 4.5 7.5 5.5 — — —
11/64 7/32 13/64 9/64 1/4 5/32 9/32 11/64 19/64 7/32
3.0 3.0 6.0 4.0 7.0 4.5 7.0 5.0 4.0 7.0 5.0
1/8 15/64 5/32 9/32 11/64 9/32 13/64 5/32 9/32 13/64
3.5 4.0 — 4.5 — — — — —
5/32 11/64
4.0 3.5 — 4.5 — 5.5 4.0 — 5.0
9/64 11/64 7/32 5/32 13/64
5.0 4.0 — — — — 5.0
5/32 13/64
Dimensions and pressures for reference only, subject to change.
*For Seal-Lok Lite only.
**For both Seal-Lok and
Seal-Lok Lite.
*For Seal-Lok Lite only.
**For both Seal-Lok and
Seal-Lok Lite.