Page 354 - 4300 Catalog Cover.pdf

Parker Hannifin Corporation

Tube Fittings Division

Columbus, Ohio

http://www.parker.com/tfd

S4

4300 Catalog

Equipment

Dimensions and pressures for reference only, subject to change.

Hand Tube Benders – Inch

These are sturdy, easy-to-use hand tools for fast and accurate bending without kinks

or visible flattening. Twelve individual sizes from -2 (1/8” O.D.) to -16 (1” O.D.) are

available.

Medium Duty Inch Hand Tube Benders

Designed and built for fast, accurate bends and long service life.

These are individual benders for eight inch tube sizes (1/8”, 3/16”, 1/4”, 5/16”, 3/8”,

1/2” 5/8”, 3/4”). All of these benders will bend copper, aluminum, annealed steel and

stainless steel. These can be used in hands or mounted in a bench vise.

HOWTO USE:

Simply align marks of the pressure arm and radius block, then bend to

the desired angle (up to 180°) by pulling steadily on the slide block handle.Bend angles

are indicatedon the radius block, both front andback. (Detailed instructions are included

with each bender.) See the table below for technical data and part numbers.

Recommended

Radius to Min. Wall

Max. Wall Thickness

Tube

Without

Copper,

Steel,

O.D.

Centerline

Flattening

Aluminum Stainless Steel

Size

(in.)

Part No.

2

1/8

7/16

0.012

Any

0.032.........

2-2829S

3

3/16

9/16

0.020

Any

0.032.........

3-2829S

4

1/4

9/16

0.028

Any

0.083.........

4-2829S

5

5/16

15/16

0.032

Any

0.083.........

5-2829S

6

3/8

15/16

0.032

Any

0.083.........

6-2829S

8

1/2

1 1/2

0.042

Any

0.083.........

8-2829S

10

5/8

3

0.042

Any

0.049.........

10-2829S

12

3/4

3 3/4

0.049

Any

0.065.........

12-2829S

Ratchet Hand Tube Benders

These are individual benders for three tube sizes, 5/8”, 3/4” and 7/8”, in copper, alu-

minum, annealed steel and stainless steel. They can be used in hands or mounted

in a bench vise.

HOW TO USE:

Position the tube in the bender, close the latch and pull the ratchet

handle away from radius block handle until the desired angle (up to 180°) is formed.

Bend angles are indicated on the radius block. (Detailed instructions are included with

each bender.) See the table below for technical data and part numbers.

Recommended

Radius to Min. Wall

Max. Wall Thickness

Tube

Without

Copper,

Steel,

O.D.

Centerline

Flattening

Aluminum Stainless Steel

Size

(in.)

Part No.

10

5/8

3

0.042

Any

0.049.........

10-2829

12

3/4

3 3/4

0.049

Any

0.065.........

12-2829

14

7/8

3 3/4

0.049

Any

0.065.........

14-2829

Adjustable Handle Hand Benders

These are individual benders for three tube sizes (1/4, 3/8, 1/2). All of these benders

can form accurate bends up to 180° in aluminum, copper, steel & stainless steel ma-

terials.* These benders include rollers in the bending handle to reduce effort required

for bending and they can be mounted in a bench vice.

HOW TO USE:

Simply align marks on the slide block end of the pressure arm and

radius block, then bend to the desired angle. For angles greater than 90°, the adjust-

Fig. S1 — Medium Duty Inch

Hand Tube Bender

Fig. S2 — Ratchet Hand Tube

Bender

Benders

Fig. S3 — Adjustable Handle

Hand Benders