Page 317 - Catalog4400.pdf

C-19 Hose Products Division
Parker Hannifn Corporation
Wickliffe, Ohio
www.parkerhose.com
Catalog 4400 US Equipment
B
A
C
D
E
Parkrimp Assembly Instructions
Turn on the pump by pressing the “ON” switch.
Pull the valve handle forward to bring the pusher
down for crimping. When the split die ring con-
tacts the base plate, the crimp is complete. Push
the valve handle back to lift the pusher, open the
dies, and release the finished assembly.
Note: You do not have to remove any tooling to
insert or remove straight fittings. The front half of
the split die ring and the front die train must be
removed to insert and remove bent tube fittings.
With the pusher in the
full up position, lift the
back half of the split die
ring. Lock it in the up
position by pushing the
slide pin in. (The slide
pin is located inside the
pusher at the back.)
Lubricate die bowl using a
premium quality lithium-
base grease. Carefully
insert the adapter bowl,
83C-OCB, into the base
bowl. The adapter bowl
must be tilted toward the
back of the crimper during
insertion.
Slide
Pin
Lubricate die bowl using a premium
quality lithium-base grease. Place unitized die-
train into the adapter bowl. Select die
and die ring by hose size and type. See
decal on crimper for proper die set.
Note: Die sets have color-coded cavities indicat-
ing size and have the fitting series
and dash size stamped on the top.
If required, place spac-
er ring on locating step
of adapter bowl. Refer-
ence decal on crimper
for tool selection.
Insert the proper die
set into the die bowl.
(The die sets are in
two halves of four
dies each. Place one
half in the back and
one half in the front
to accommodate
bent tube fittings.)
Reference decal on
crimper for proper
tool selection.
Lower the back half of the
split die ring onto the dies by
pulling the slide pin forward.
Slide
Pin
Insert the front half of the
split die ring aligning the
pins in the back half with
the hole in the front half.
Crimping using Superkrimp and Parkrimp 2
1 Mark insertion depth and push on ftting
For 81 Series Shells with 88 Series Fittings
2a If using large two-piece dies
2b If using small unitized dies
Color-Coded
Unitized
Die-Train
Parkrimp Fittings Series 25, 26, 43, 70, 71, 73, 76, 78, S6, 81, HY
3 Place spacer ring
Important: Hose assemblies
must be inspected for cleanliness
and free of all foreign particles.
Standard
Parkrimp Series
26 Series
Crimp
Diameter
26 Series Parkrimp Series 81 Series
Mark the hose insertion depth
and push hose into fitting until the
mark on the hose is even with the
end of the shell. Lubricate hose
if necessary, however, DO NOT
lubricate if using spiral hose.
See Hose Insertion Depth table
on previous page.
Place 81 Series
Shell onto end of
hose and make
sure the end of the
shell lines up with
the Insertion Depth
mark.
Push hose onto the
88 Series fitting until
the shell bottoms
against the fitting’s
stop ring or hex.
Lubricate hose if
necessary.
Position the hose and fitting in dies from below.
Rest bottom of coupling on die step using the PARKALIGN ® feature.
5 Position the ftting
6 Crimp hose
4 Position the split die ring
Measure crimp
diameter on the
flat surfaces of
the crimped shell,
referenced in the
illustration to the
right. Reference
decal on crimper
for crimp diam-
eters. Never use
hose assemblies
with incorrect
crimp diameters.
7 Measure crimp diameter