Page 316 - Catalog4400.pdf

C-18 Hose Products Division
Parker Hannifn Corporation
Wickliffe, Ohio
www.parkerhose.com
Equipment Catalog 4400 US
A
B
C
D
E
Parkrimp Assembly Instructions
Mark the hose insertion depth
and push hose into fitting
until the mark on the hose is
even with the end of the shell.
Lubricate hose if necessary,
however, DO NOT lubricate if
using spiral hose. See Hose
Insertion Depth table below.
Place shell onto end of
hose and make sure
the end of the shell
lines up with the Inser-
tion Depth mark.
Push hose onto the
88 Series fitting until
the shell bottoms
against the fitting’s
stop ring or hex.
Lubricate hose if
necessary.
Position the hose and fitting in dies from below.
Rest bottom of coupling on die step using the PARKALIGN ® feature.
26 Series Parkrimp Series 81 Series
Crimping using Minikrimp, Karrykrimp, Karrykrimp Bench Mount, Karrykrimp 2
and Karrykrimp 2 Bench Mount
Pull pin at the top
of pusher to swing
it back. Place
unitized die-train
into base plate.
See decal on
crimper for proper
die set.
Note: Parkrimp 1
does not have a
pin at the top of
the pusher.
Important:
Lubricate the
crimper’s die bowl
using a premium
quality lithium-
base grease.
Color-Coded
Unitized
Die-Train
Place correct die ring
on top of the dies. See
decal on crimper for
proper die ring.
Position pusher by
replacing the pin and
operate pump until the die
ring bottoms out. Release
pressure within the pump
— remove finished
assembly.
Note: Minikrimp,
Karrykrimp & Karrykrimp
2 have several types of
power sources, all of which
are separate units from the
crimping machine.
For 81 Series Shells with 88 Series Fittings
2 Insert unitized die train
4 Place die ring and crimp
5 Measure crimp diameter
Parkrimp Fittings Series 25, 26, 43, 70, 71, 73, 76, 78, S6, 81, HY
Standard
Parkrimp Series
26 Series
Crimp
Diameter
Measure crimp diameter on the flat surfaces of the
crimped shell, referenced in the illustration
to the left. Reference decal on crimper for crimp
diameters. Never use hose assemblies with
incorrect crimp diameters.
Important: Hose assemblies must be inspected for
cleanliness and free of all foreign particles.
For specifc information on crimping, visit CrimpsourceTM online at www.parker.com/crimpsource.
Hose insertion depths
Fitting
Size
Fitting Series
25 26 43 70 71 73 77 78 S6 79 81 HY
inch mm inch mm inch mm inch mm inch mm inch mm inch mm inch mm inch mm inch mm inch mm inch mm
-4 — — 13/16 21 13/16 21 — — — — — — — — — — — — — — — — 1-7/16 37
-5 — — 13/16 21 15/16 24 — — — — — — — — — — — — — — — — — —
-6 7/8 22 13/16 21 1-1/8 29 1-1/16 27 1-1/16 27 — — — — — — — — — — — — 1-1/2 40
-8 7/8 22 13/16 21 1-5/16 33 1-5/16 33 1-1/4 32 — — 1.36 34.6 — — — — — — — — 1-9/16 40
-10 — — 7/8 22 1-9/16 40 1-3/8 35 1-5/16 33 — — 1.53 38.9 1-7/8 47 — — — — — — 1-9/16 40
-12 — — 7/8 22 1-1/2 38 1-1/2 38 1-7/16 37 1-7/8 48 1.78 45.2 1-7/8 48 — — 2-3/16 56 1-1/8 29 1-5/8 40
-16 — — 1 25 1-3/4 44 1-13/16 46 1-3/4 44 2 51 2.13 54.1 2 51 — — 2-5/16 59 1-1/4 32 1-3/4 43
-20 — — 1 25 1-7/8 48 1-3/4 44 1-13/16 46 2-1/2 64 2.51 63.8 2-1/2 64 — — 2-13/16 71 1-5/16 33 — —
-24 — — 1-1/16 27 1-7/16 37 — — 2-5/16 59 2-7/16 62 — — 2-7/16 62 — — — — 1-5/16 33 — —
-32 — — 1-1/4 32 1-13/16 46 — — 2-7/16 62 2-13/16 71 — — — — 3-1/2 88 — — 1-11/16 43 — —
1 Mark insertion depth and push on ftting
3 Position the ftting