Page 57 - Good Year Rubber Products 2012 Goodyear EP Conveyor Belt Catalog

55
G L I D E ® P L U S
GLIDE PLUS CONVEYOR BELT DATA - Metric
150mm narrower widths are possible if the belt is broken in for an extended period of time fully loaded. Consult your GTM.
Glide Glide Glide Glide Glide Glide Glide Glide Glides Glide
400/2 500/2 600/3 750/3 800/4 1000/2 1000/4 1250/5 1350/3 1800/4
Number Of Plies 2 2 3 3 4 2 4 5 3 4
20 degree idlers 457 610 610 610 762 610 762 914 762 914
35 degree idlers 610 762 762 762 914 762 914 1067 914 1067
45 degree idlers 762 914 914 914 1067 914 1067 1219 1067 1219
GLIDE PLUS TROUGHABILITY (Minimum Belt Width) (mm) (Table based on ISO 703 Testing Procedure)
On In-Line systems with troughing idler spacing greater than 1.5m or idler roll gap greater than 12.7mm Consult your GTM.
Material Weight 0-640 kg/cu.m. 641-1,280 kg/cu.m.
Idlers 20 deg 35 deg 45 deg 20 deg 35 deg 45 deg
Glide 400/2 1219 1219 1067 1067 1067 914
Glide 500/2 1524 1372 1219 1372 1219 1067
Glide 600/3 1829 1524 1372 1829 1524 1372
Glide 750/3 1829 1524 1372 1676 1524 1372
Glide 800/4 2134 1829 1829 2134 1829 1524
Glide 1000/2 1829 1829 1524 1829 1524 1372
Glide 1000/4 2134 1829 1829 2134 1829 1524
Glide 1250/5 2743 2438 2438 2743 2438 2134
Glide 1350/3 2438 2438 2134 2438 2134 1829
Glide 1800/4 2997 2997 2743 2743 2743 2438
GLIDE PLUS LOAD SUPPORT (Maximum Belt Width) (mm)
Glide Glide Glide Glide Glide Glide Glide Glide Glides Glide
400/2 500/2 600/3 750/3 800/4 1000/2 1000/4 1250/5 1350/3 1800/4
Number Of Plies 2 2 3 3 4 2 4 5 3 4
Over 80% Tension 559 559 610 610 762 762 914 1067 914 1067
61% to 80% Tension 457 457 508 508 610 610 762 914 762 914
40% to 60% Tension 406 406 457 508 508 610 610 762 762 914
Up to 40% Tension 356 356 406 457 457 508 508 610 610 762
Tails and Snubs 356 356 406 457 457 508 508 610 610 762
GLIDE PLUS Minimum pulley diameters (mm)
Glide Glide Glide Glide Glide Glide Glide Glide Glide Glide
400/2 500/2 600/3 750/3 800/4 1000/2 1000/4 1250/5 1350/3 1800/4
Number Of Plies 2 2 3 3 4 2 4 5 3 4
Fabric Type P/P P/N P/P P/N P/P P/N P/N P/N P/N P/N
Vulcanized & Fastener Rating (kN/m) 70 88 105 131 140 175 175 210 236 315
Carcass Gauge (mm) 5.13 5.49 6.38 6.91 8.64 7.82 9.35 11.79 11.20 15.11
Carcass Weight (kg/m2) 6.22 6.31 7.57 8.20 10.16 10.20 12.06 14.01 14.55 19.58
Approx. 1/32" cover wt (kg/m2) 1.17 1.17 1.17 1.17 1.17 1.17 1.17 1.17 1.17 1.17
Elastic modulus (kN/m) 6,745 6,445 10,115 9,670 13,485 10,510 12,896 16,110 15,760 21,900
Avg. Permanent Elongation (%) * 0.9 1.4 0.9 1.4 0.9 1.5 1.4 1.4 1.5 1.5
Splice Step Length (mm) 406 457 406 457 406 Finger 457 457 Finger Finger
Recommended Fastener Plate BR-10 BR-10 BR-10 BR-14 BR-14 NR NR NR NR NR
Hinge R5 R5-1/2 R5-1/2 R6 R6 R6 R6 R6 R8 NR
Hinge U35 U35 U35 U36 U36 U38A U38A U38 U38 U38B
Rated belt tension can exceed 100%, with a maximum of 150%, during starting and stopping conditions. Fastener size recommendation may vary due to cover thickness, pulley diameters, and system tension.
Consult your GTM or fastener manufacturer. R6 fasteners must be installed with stainless steel rivets when belt tension exceeds 140kN/m for best results.
P/N = Poly / Nylon
* Average permanent elongation values at 100% of rated belt tension are based on ISO 9856 test procedure. Consult your GTM or GAD for elastic & total elongation calculations.
Consult your GTM for vulcanized splice method for 1000/2, 1350/3, and 1800/4 constructions. (Do not use any bias or overlap design). Minimum cover thickness is 3.175mm for vulcanized splice.