Page 330 - DPL413 Complete Catalog for web_wm

Brass Fittings
H
DPL413 877.963.4966 • dixonvalve.com 328
Caution: Push-on fittings will properly grip push-on hose
only when pushed all the way in, with the cut end of the
hose completely concealed by the plastic cap.
Push-On Fittings
Rigid Tube x Push-On Hose Barb
Push-On Hose Menders
90° Push-On Hose Barb x Male NPTF Elbows - Forged
Tool for Push-On Fittings
Dixon push-on fittings are intended for use with Lok-On (push-on style) hose only. No hose clamps or ferrules
are needed. Lok-On fittings will properly grip Lok-On hose only when pushed all the way in, with the cut end of the hose
completely concealed by the plastic cap.
Hose ID Tube OD Brass Opt Qty
Part # Price/E
1/4" 3/16" 294-0403 $3.09 100
1/4" 1/4" 294-0404 2.48 100
1/4" 5/16" 294-0405 3.11 100
3/8" 3/8" 294-0606 3.31 50
1/2" 1/2" 294-0808 4.81 50
5/8" 5/8" 294-1010 7.09 25
3/4" 3/4" 294-1212 10.98 25
Hose ID NPTF Thread Brass Opt Qty
Part # Price/E
1/4" 1/8"-27 273-0402 $4.22 100
1/4" 1/4"-18 273-0404 5.27 50
3/8" 1/8"-27 273-0602 6.48 50
3/8" 1/4"-18 273-0604 6.19 50
3/8" 3/8"-18 273-0606 7.24 25
1/2" 3/8"-18 273-0806 9.12 25
1/2" 1/2"-14 273-0808 11.50 25
3/4" 1/2"-14 273-1208 23.13 10
3/4" 3/4"-14 273-1212 22.31 10
Hose ID Brass 303 Stainless Opt
Qty Part # Price/E Part # Price/E
1/4" BPM2 $2.81 SSPM2 $33.47 100
5/16" BPM25 3.16 --- --- 100
3/8" BPM3 3.36 SSPM3 38.45 50
1/2" BPM4 5.31 SSPM4 42.42 50
5/8" BPM5 7.65 --- --- 25
3/4" BPM6 9.06 --- --- 25
1" BPM8 15.38 --- --- 10
Features:
• cuts push-on style hose and inserts the fitting
• Built-in cutter slices through ¼" - ¾" ID reinforced push-on
hose without fraying.
• Clamp hose into tool's vice and apply light pressure on
handle to drive in the fitting.
• tool has four 7/16" diameter mounting holes for bench
mounting
• overall size is 13-1/2" long x 2-3/8" wide x 7" height
Size Part # Price/E
¼" - ¾" 270AT $1094.37
Hose Assembly Tool
Part # Price/E
HHCI $220.00
Assembly Instructions:
1. Trim hose end with smooth square cut
2. Lubricate either push-on fitting, hose or both.
3. Insert push-on fitting into hose until first barb is in hose.
4. Place end of fitting against a flat object (bench, wall, etc.)
and grip the hose one inch from end. Push with a steady
force until end of hose is covered by yellow plastic cap.
Disassembly Instructions:
1. Leaving push-on fitting in place, make a 1" cut in the hose
along the barbed end of the fitting. Note: Be careful not to
nick barbs when cutting the hose.
2. With firm grip on hose, give a sharp downward pull to
release the fitting from the hose.
• installs 1/4", 5/16" and 3/8" hose fittings
• lightweight, portable, comfortable cushioned grip
• economical