Page 378 - 4300 Catalog Cover.pdf

Parker Hannifin Corporation
Tube Fittings Division
Columbus, Ohio
http://www.parker.com/tfd
S28
4300 Catalog Equipment
Dimensions and pressures for reference only, subject to change.
Rolo-Flair®
Manual Rotary Flaring Tool
(For soft metal tube)
Precision burnished 37° and 45° flares in tube sizes from 2
(1/8” O.D.) to 12 (3/4” O.D.) with an easy turn of the handle. For
use with copper and aluminum alloys. A depth gauge allows
proper positioning of tube for consistent flaring.
HOWTOUSE: Open die, insert tube up to the gauge and clamp
the tube in the die. Turn drive handle clockwise to flare, then
counterclockwise for retracting flaring cone. Open clamping
die by loosening wing nut and remove flared tube.
Part Name Part No.
Rolo-Flair for 37° flares
(for 1/8”, 3/16”, 1/4”, 5/16”, 3/8”, 1/2”, 5/8”, 3/4”, O.D.) ........ 212FB
Rolo-Flair for 45° flares
(for 1/8”, 3/16”, 1/4”, 5/16”, 3/8”, 1/2”,5/8”, 3/4”, O.D.) ......... 945TH
Fig. S64 — Rolo-Flair
Flaring Tools
Fig. S65 — 210A Combination
Flarer
Fig. S66 —Vise Block with
Flaring Pin
Combination Flarer
For 1/8”, 3/16”, 1/4”, 5/16”, 3/8”, 1/2”, 5/8”, O.D. tube.
Thecombinationflarer isa7-in-1 impact tool for flaring (37°) soft
copper, aluminum and fully annealed steel tube, sizes 2 (1/8”
O.D.) through 10 (5/8” O.D.). Maximum wall thickness: 1/8” to
3/8” is 15% of tube O.D., 1/2” and larger is 10% of tube O.D.
HOW TO USE: Insert tube into proper flare hole and fasten
with clamping screw. Set hardened-steel flaring punch in tube
and form flare with a few sharp hammer blows. (Tube should
not project more than 1/16” above top of block.)
Vise Block with Flaring Pin
These impact 37° flaring tools are for use with copper, alum-
inum alloy, and thin wall steel or stainless steel. Separate
tool-ing set for each tube size 4 (1/4” O.D.) through 24 (1 1/2”
O.D.).Maximumwall thickness: 1/8” to 3/8” is 15%of tube O.D.,
1/2” and larger is 10% of tube O.D.
HOWTO USE: Clamp tube flush in matching halves of block
in a bench vise. Give hardened steel flaring pin a few sharp
blows with a hammer to form the flare.
Tube O.D.
Size (in.) Part No.
4 1/4 ........................................................................... 4-2866
5 5/16 .......................................................................... 5-2866
6 3/8 ........................................................................... 6-2866
8 1/2 ........................................................................... 8-2866
10 5/8 ........................................................................... 10-2866
12 3/4 ........................................................................... 12-2866
14 7/8 ........................................................................... 14-2866
16 1 ............................................................................. 16-2866
20 1 1/4 .......................................................................... 20-2866
24 1 1/2 .......................................................................... 24-2866
Order vise block with flaring pin using part numbers above.
The block and pin may be ordered separately by suffixing the
part number with either Pin or Block. 4-2866 Block
Part Number Example:
Part No.
210A