Page 193 - 4300 Catalog Cover.pdf

G5 Parker Hannifin Corporation
Tube Fittings Division
Columbus, Ohio
http://www.parker.com/tfd
4300 Catalog Pipe Fittings and Port Adapters
Dimensions and pressures for reference only, subject to change.
Application Guidelines for Tapered Threads
Straight Connectors with NPT/NTPF 3/4-14 and Smaller
Straight connectors with 3/4-14 NPT/NPTF and smaller male
pipe threads have very high pressure holding capability and seal
reliability when used in applications without “make and break”
(such as maintenance) requirements.
They are also well suited for low cycle non-pulsating (static)
applications with pressures in excess of 6,000 psi.
Straight Connectors with NPT/NPTF above 3/4 -14 and
All Shaped Connectors with NPT/NPTF Threads
It is difficult to always tighten shapes with pipe threads to an
optimum tightness level because of orientation requirements.
Also, all connectors in this category with pipe threads have low
reliability for leak free operation in dynamic applications.There-
fore, they are not preferred where a leak free joint is required.
All NPTF Connectors
While a pipe thread connection can be disassembled and re-
assembled in low-pressure systems, it is not intended to be a
frequently assembled and disassembled connection. (When
connectors are known to be disassembled and re-assembled
repeatedly, pipe connections are not preferred for high-pres-
sure systems.)
For theaboveapplications, aport connectionwithanelastomeric
seal, such as SAE straight thread port (SAE J1926/ISO11926),
SAE four bolt split flange (SAE J518/ISO 6162), and ISO 6149
is recommended.For applicationswhereelastomeric seals can’t
be used, consult the manufacturer.
As noted, BSPT and metric taper are designed and perform
similarly. Follow the NPT/NPTF guidelines for their application.
In general, tapered thread connections have the following
limitations which should be considered when specifying port
connections:
• Poor dynamic sealing characteristics
• Possible expansion, and even cracking, of the port
• Orientation is a concern in shaped connectors
• Larger threads are more prone to leakage because of
more potential leak points
• System contamination due to thread sealant
• Prone to galling, especially in stainless steel
• Limited remakeability
Parallel Thread Adapters
Straight, or parallel, thread ports in various forms are becom-
ing more popular in hydraulic systems because they are more
reliable and easier to service.
Three types of threads are used for parallel thread ports:
• UN/UNF (SAE straight thread)
• BSPP (British Standard Pipe, Parallel)
• Metric parallel
Because parallel threads only serve one function (i.e. holding
the fitting in place), some other means of sealing is always
present, such as an elastomeric O-ring or a metal seal. There
are many variations of sealing methods, and in some cases,
they are interchangeable among the different thread forms and
may appear to be similar.
UN / UNF Threads
SAE J1926 uses UN/UNF threads and is often referred to as
SAE Straight Thread. The female port is often referred to as
ORB or O-ring boss. This port style, shown in Fig. G4, is widely
used in North America.
Fig. G4 —Typical O-Ring Boss Port
BSPP
In Europe, Japan and many other former Commonwealth
nations, the British Standard Pipe thread form, BSP, is still
used extensively to connect pipes and components in hydraulic
systems. The BSP thread is offered in a straight (parallel) form
known as BSPP and a tapered form known as BSPT. These
threads feature a 55° flank angle. Fittings in this section with
male BSPP threads use a primary sealing method of an O-ring
and retaining ring, as shown in Fig. G5.
Fig. G5 — O-Ring with Retaining Ring
Additional sealingmethods such as a cutting face or an EOlastic
seal, as shown in Fig. G6, are also available on other fittings
within the catalog.TheseBSPP fittings are all designed to thread
into a female BSPP port (ISO 1179), however, the seal is cre-
ated with one of the aforementioned sealing methods, not with
the threads. It is also important to note that with these BSPP
threaded connections, the seal occurs on the port surface, or
spotface, not in an O-ring gland or chamfer as SAE and ISO-
6149 straight thread do. A detail of the BSPP port is shown on
page U29.
Fig. G6 — O-Ring in Fitting Groove