Page 70 - ExpansionJointsCatalog2010

190-D
450
SERIES
sleeve type pipe connectors
SERIES
7" Length Face-To-Face
External Ring
Internal Ring 2" Soft
Cuff
Sealing Bead
I. D. Of JointO. D. Of Pipe
NATIONAL ASSOCIATION OF HOSE
AND ACCESSORIES DISTRIBUTORS
INDEPENDENT
SEALING
DISTRIBUTORS
The Expansion Joint People
Protecting Piping And
Equipment Systems
From Stress/Motion
Nominal
Pipe
Size
O.D. of
Pipe
I.D. of
Joint
Length
of
Joint Extension Compression
Angular
±
Degrees
Axial
Compression
Axial
Extension Sleeve
Pressure
(PSIG)
Note 1
Vacuum
(In. Hg.)
Temp F°
Note 2
Axial
Dimensions Allowable Movements Operating Conditions Force To
Move (Lbs.)
Wt.-
Lbs.
1.5 1.900 7.0 .5 1.0 10 ° 75 20 225 30 26 1.4
2.0 2.375 7.0 .5 1.0 10 ° 75 20 225 35 30 1.6
2.5 2.875 7.0 .5 1.0 10 ° 75 20 225 40 34 1.8
3.0 3.5 7.0 .5 1.0 10 ° 75 20 225 45 40 2.0
3.5 4.0 7.0 .5 1.0 10 ° 75 20 225 48 43 2.2
4.0 4.5 7.0 .5 1.0 10 ° 75 20 225 50 45 2.4
4.5 5.0 7.0 .5 1.0 10 ° 75 20 225 53 52 2.7
5.0 5.563 7.0 .5 1.0 10 ° 75 20 225 57 60 2.9
6.0 6.625 7.0 .5 1.0 10 ° 75 20 225 65 75 3.4
8.0 8.625 7.0 .5 1.0 10 ° 75 20 225 100 145 4.3
10.0 10.750 7.0 .5 1.0 10 ° 75 20 225 265 255 5.1
12.0 12.750 7.0 .5 1.0 10 ° 75 20 225 650 400 6.7
Coupling to be slipped over pipe to a depth of 2".
Coupling is a flexible member, and pipe must be properly anchored and guided.
All dimensions are in inches.
Notes: 1. Burst pressure rated at four times operating pressure.
2. Can withstand an intermittent temperature of 275° F.
The PROCO Series 450 Sleeve Type Pipe Connectors are used for tough
demanding applications found in: Refridgeration Pump Systems, In-
dustrial Process Piping Systems, Power Generating Plant Pump Sys-
tems, Pulp/Paper Plant Pump Systems, Water-Wastewater Sewage and
control systems where lower pressure and sleeve ends are used in lieu
of flanged spool type rubber expansion joints. The Series 450 Sleeve
Type Pipe Connectors are constructed of Neoprene rubber and rein-
forced with impregnated woven nylon.
The PROCO Series 190-D Navy Sleeve Type Pipe Connectors are used
for tough demanding marine applications found in: Shipboard Fuel Oil,
Ballast and Bilge Drainage Systems. (The PROCO Series 190-D Navy
Sleeve Type Pipe Connectors are constructed of the same materials as
the Series 450 and come with an aluminized glass cloth outer cover to
meet Mil-E-15330 Class B specification.)
Specify the PROCO Series 190-D and Series 450 for installations near
mechanical equipment in piping systems to: (1) Absorb Pipe/Move-
ment/Stress, (2) Reduce system Noise, (3) Isolate Vibration, (4) Elimi-
nate Electrolysis, (5) Compensate Alignment/Offset & (6) Protect
Against Start-Up/Surge Forces. Our history in expansion joint prod-
ucts dates back to 1930. When you need an engineered solution to a
piping systems problem, call PROCO.
Construction of Sleeve Type Pipe Connectors: The Series 190-D and
Series 450 Sleeve Type Connectors are constructed of neoprene rubber
and reinforced with impregnated woven nylon. Sealing beads are molded
on the interior of the sleeve and provide extra sealing action for the clamp-
ing area. Internal reinforcing rings prevent deformation of the connector
during surge or temporary negative pressure conditions. The outer rein-
forcement rings are provided to add external reinforcement.
Fastening Method: The Series 190-D and Series 450 Sleeve Type Pipe
Connectors require heavy duty, stainless steel, 1" wide “T” bolt clamps to
provide proper clamping strength. Clamps are not stocked by PROCO Prod-
ucts, Inc. and are to be provided by others.
™