Page 32 - ExpansionJointsCatalog2010

SEO Version

DISTRIBUTED BY:
Warning: Expansion joints may operate in pipelines or equipment carrying
fluids and/or gases at elevated temperatures and pressures. Normal precau-
tions should be taken to make sure these parts are installed correctly and
inspected regularly. Precautions should be taken to protect personnel in the
event of leakage or splash. Note: Piping must be properly aligned and an-
chored to prevent damage to an expansion joint. Movement must not exceed
specified ratings and control units are always recommended to prevent dam-
age in the event other anchoring in the system fails. Properties applications
shown throughout this data sheet are typical. This information does not con-
stitute a warranty or representation and we assume no legal responsibility or
obligation with respect thereto and the use to which such information may
be put. Your specific application should not be undertaken without indepen-
dent study and evaluation for suitability.
PROCO PRODUCTS, INC.
2431 North Wigwam Dr. (95205)
P.O. Box 590 • Stockton, CA
95201-0590 • USA
TOLL-FREE PHONE: (800) 344-3246
NATIONWIDE AND CANADA
FACSIMILE: (209) 943-0242
(209) 943-6088
INTERNATIONAL
email: sales@procoproducts.com
website: http://www.procoproducts.com
Retaining
Rings
Rubber
Washer
Steel
Washer
Nominal
Pipe Size
Joint I.D.
Standard
Pipe
Flange
Optional
Compression Sleeve
Control Rod Bolt Circle
Flange/Retaining Ring O.D.
Bolt Circle
Equally Spaced
Bolt Holes
Bolt Circle
Split
A
A
Neutral Length
Retaining Rings
Section AA
A
Equally Spaced
Bolt Holes
Bolt Circle
A
Bolt
Holes
Dia.
Flange & Ret. Ring O.D.
Nominal Pipe Size
Joint I.D.
Figure 1: Detail Of Style 261R
Ret. Ring I.D.
Control
Rod
Plate
molded wide arch expansion joints
PROCO
™
Series 261R Products Are
Designed To Absorb Different
Movements Concurrently.
Axial Compression
Axial Elongation
Angular Movement
Bending Of The Centerline
Torsional Movement
Rotation About The Centerline (Twist)
Lateral Movement
Shear Or Perpendicular To Centerline
Absorbing Vibration
Notes:
1. Movements shown are non-concurrent.
2. Torsional movement is expressed when the expansion joint is at neutral length.
3. To determine “end thrust,” multiply thrust factor by operating pressure of system.
4. Pressure rating is based on 194
°
F operating temperature. At higher temperature
the pressure rating is slightly reduced.Vacuum rating is expressed when
expansion joint is at neutral length.
5. Weights are approximate.
6. Control unit weight consists of one rod, four washers, three nuts and two control
rod plates. Multiply number of control units needed for application (as specified in
the Fluid Sealing Association Technical Handbook) to determine correct weights.
7. Dimensions shown are in accordance with 125/150# standards of ANSI B-16.1,
B-16.24, B-16.5; AWWA C-207 Table 1 and 2 Class D.
Table 2: Sizes • Movements • Spring Rates • Pressures • Weights • Drilling
EXPANSION
JOINT SIZE
Nom. I.D. x
Inch / (mm)
NEUTRAL
LENGTH
Inch / (mm)
Flange Dimensions and Drilling
7
Weights in lbs / (kgs)
5
Positive PSIG / (Bar)
Vacuum
Inches of Hg / (mm of Hg)
Expansion Joint
Retaining Ring Set
Control Unit
6
Assembly
O.D. of Expansion
Joint / Ring
Inch / (mm)
Bolt Circle
Inch / (mm)
Numb
er of Holes
Size of Holes
Inch / (mm)
261R Movement Capability: From Neutral Position
1
Axial Compression
Inch / (mm)
Axial Extension
Inch / (mm)
Lateral Deflection
Inch / (mm)
Angular Deflection
Degrees
Torsional Rotation
2
Degrees
Thrust Factor
3
In2 / (cm2)
Force Pounds for 1"
Axial Extension
lb/in / (N/mm)
Force Pounds for 1"
Lateral Deflection
lb/in / (N/mm)
Operating
4
Conditions
Spring Rates
Force Pounds for 1"
Axial Compression
lb/in / (N/mm)
0.625 0.750 28
°
5
°
11.04 126 182 149 225 24 1.3 2.5 2.3 5.00 3.88 4 0.625
(16)
(19)
(71)
(22)
(32)
(26)
(15.5)
(610)
(0.59)
(1.1)
(1.0)
(127.0) (98.55)
(15.88)
0.625 0.750 25
°
5
°
14.18 132 158 130 225 24 1.7 4.0 2.8 6.00 4.75 4 0.750
(16)
(19)
(92)
(23)
(28)
(23)
(15.5)
(610)
(0.77)
(1.8)
(1.3)
(152.4) (120.65)
(19.05)
0.625 0.750 20
°
5
°
17.71 128 141 111 225 24 2.1 4.5 2.8 7.00 5.50 4 0.750
(16)
(19)
(114)
(22)
(25)
(19)
(15.5)
(610)
(0.95)
(2.0)
(1.3)
(177.8) (139.70)
(19.05)
0.625 0.750 18
°
5
°
21.64 139 208 133 225 24 2.4 5.5 2.8 7.50 6.00 4 0.750
(16)
(19)
(140)
(24)
(36)
(23)
(15.5)
(610)
(1.0)
(2.5)
(1.3)
(190.5) (152.40)
(19.05)
0.625 0.750 14
°
4
°
30.66 110 180 105 225 24 3.2 6.0 2.8 9.00 7.50 8 0.750
(16)
(19)
(198)
(19)
(32)
(18)
(15.5)
(610)
(1.4)
(2.7)
(1.3)
(228.6) (190.50)
(19.05)
0.625 0.750 13
°
4
°
41.26 143 190 136 225 24 3.6 8.5 4.0 10.00 8.50 8 0.875
(16)
(19)
(266)
(25)
(33)
(24)
(15.5)
(610)
(1.6)
(3.9)
(1.8)
(254.0) (215.90)
(22.23)
0.625 0.750 12
°
4
°
53.43 136 166 147 225 24 4.9 9.5 4.0 11.00 9.50 8 0.875
(16)
(19)
(345)
(24)
(29)
(26)
(15.5)
(610)
(2.2)
(4.3)
(1.8)
(279.4) (241.30)
(22.23)
0.625 0.750 12
°
4
°
82.47 226 230 210 210 24 7.7 14.5 8.0 13.50 11.75 8 0.875
(16)
(19)
(532)
(40)
(40)
(37)
(14.8)
(610)
(3.5)
(6.6)
(3.6)
(342.9) (298.45)
(22.23)
0.750 1.0 12
°
4
°
135.13 248 381 281 210 24 13.9 17.0 10.0 16.00 14.25 12 1.000
(19)
(25)
(872)
(43)
(67)
(49)
(14.8)
(610)
(6.3)
(7.7)
(4.5)
(406.4) (361.95)
(25.40)
0.750 1.0 11
°
4
°
179.46 378 493 409 210 24 19.5 24.5 10.0 19.00 17.00 12 1.000
(19)
(25)
(1158)
(66)
(86)
(72)
(14.8)
(610)
(8.8)
(11.0)
(4.5)
(482.6) (431.80)
(25.40)
0.750 1.0 11
°
3
°
230.08 423 592 497 150 24 22.7 27.0 12.0 21.00 18.75 12 1.125
(19)
(25)
(1484)
(74)
(104)
(87)
(10.3)
(610)
(10.3) (12.3)
(5.4)
(533.4) (476.25)
(28.58)
0.750 1.0 10
°
3
°
286.98 432 606 509 150 24 26.8 33.5 15.0 23.50 21.25 16 1.125
(19)
(25)
(1852)
(76)
(106)
(89)
(10.3)
(610)
(12.2) (15.3)
(6.8)
(596.9) (539.75)
(28.58)
0.750 1.0 8
°
3
°
350.15 543 761 690 150 24 29.5 34.0 16.0 25.00 22.75 16 1.250
(19)
(25)
(2259)
(95)
(133)
(121)
(10.3)
(610)
(13.4) (15.5)
(7.2)
(635.0) (577.85)
(31.75)
0.750 1.0 8
°
3
°
419.61 628 829 776 150 24 31.8 38.0 16.0 27.50 25.00 20 1.250
(19)
(25)
(2707)
(110)
(145)
(136)
(10.3)
(610)
(17.3) (17.3)
(7.2)
(698.50) (635.00)
(31.75)
1.5
(40)
2
(50)
2.5
(65)
3
(80)
4
(100)
5
(125)
6
(150)
8
(200)
10
(250)
12
(300)
14
(350)
16
(400)
18
(450)
20
(500)
6
(150)
8
(200)
1.5
(38)
2.25
(57)